Colloidial Silver Do it Yourself

[Swanny]

Originally Posted by malakai

BEST are 12vdc output and at least 1 WATT
but 5+ is even better.

you will need a wallwart of at least 12vdc@500ma but the larger the
better.

you can do the same with a CIGARETTE LIGHTER PLUG. works even better
because it's 12vdc and will work anywhere you have access to a cigarette
lighter plug.

you can also do the same thing with a small solar cell or even just two
pieces of wire hooked up to ANY electrical source of 9 volts or greater.

So I could use a 12v car battery???

[nagual]

Originally Posted by Swanny

So I could use a 12v car battery???

there are different opinions about the voltage needed...


I'm using 19,2 v (constant current) with excellent results...

[Sarahmay]

So the "Blue Man" was on the Today show again this morning for a follow up story. An attempt by the PTB to discourage people from taking colloidal silver for H1N1? I think so...

[Anchor]

Yay ! The first ever batch made at Anchor's house

The link here goes to a picture in my album showing what I made...
http://www.projectavalon.net/forum/a...pictureid=6884

The device on the right is a TDS meter, so I can tell how many parts per million I have managed.

This one is weak solution - it took about 9hrs to brew, starting from home steam distilled water. The rig I used was from an Aussie distributor (www.silverwell.com.au), but I think they are made in the US.

It looks pale yellow. I get a good tindal effect if I shine a laser through it. I have enough 99.99% pure silver to make about 400L if I need to, and the solar power to do it whatever happens.

Getting there!

A..

[Swanny]

Nice one

[Anchor]

Originally Posted by Swanny

Nice one

Thanks

I have been reviewing the various recommendations here and elsewhere on the interwebs and there appears to be some inconsistency and inaccuracy presented regarding the purity of silver required in the electrodes. The confusion is in the number of 9's used to describe the purity, and whether or not the description is a percentage or not.

From my reading the baseline purity is that the silver used for the electrodes must be 99.99% pure, alternately referred to as 9999+, short for 9999 parts to 10000 of silver, rest is impure, also seen as 999.9/1000!

Bullion grade silver is only 99.9% (999+) pure which allows enough impurities to potentially cause problems. You would probably only want to do this if it was an emergency and if you didn't have the right silver, but you were not planning long term treatment.

Use of most silver coins not recommended. There are exceptions to this (Canadian Maple for example, which is 9999 pure) but most are only 999 pure or worse. For example: Brittania grade silver (used for UK bullion coins) is only 97.5% (975) pure and Sterling silver is only 92.5% (925) pure. With these coins you still get your troy oz's of silver, but it is an alloy, the coins weigh in at more than their Troy oz content due to the addition of other metals to toughen them up. Don't make electrodes out of these!

It is possible (but very expensive) to get 99.999% pure silver. This is very rare and specialized material. Personally I wont be doing that. By my estimate the equivalent size to the ones I have in 99999 silver would be AUD$200 or more, when the 9999 electrodes are AUD$25 and seem good to me.

In general 99.9% is not thought by many as really pure enough if you intend on taking lots of the colloidal silver internally over a long time. Personally I agree with them, but as ever there is no hard research to back this up, just hearsay. I do think there is a case for moving to the next higher grade (9999) as this reduces the impurities by a factor of 10.

A..

[kari]

Hi, i used 30 volt DC,and the way i did it is as follows:first i got water for injection(distilled water works as well) and i heated it up in the microwave until it started to boil,then i took my silverrods(pure silver 99,99999) and sunk them down in the heated water and run the 30 volts thru it,the volume was about 70 centiliteres, i did not add any salt to the water, after 10 minutes i heated it again in the microwave (until it started to boil),after the first 10 minutes the water had not turned yellow, but after the next 10 minutes it started to shift in to yellow, and i heated it again and then it got to be the right color, first when i tasted the water, it tasted a bit like metal, but that`s because my silver was low in my body,after a few days it tasted almost like normal water, the thing is, when i did my silverwater it worked best when i used a jugg that had almost straight sides,and the silverrods,aproxametly(sorry for my spelling) 2-3 centimeteres apart,anyone can di this,i bought my silver from the company that deliveres to all the jewelerystores, they have the"finesilver" that is needed for making colloidalsilver, nothing but the purest silver is good enough, i bought 3 meters (2-3mm in diameter)of silverrod,it cost me 700 kr. and that is in dollars aprox. 100 dollars i think.golden color is the key and pure water(distilled) the heat makes it alright,no need for salt.30 vdc i have found works the best.kari

[Anchor]

Quick Update:

After a weeks, "risky" research, I can confirm that my 8ppm CS brew when used in one a spray bottle makes excellent under-arm deoderant.

The only cosmetics in my bathroom now are soap, shaving soap, toothpaste, shampoo and colloidal silver.

A..